Home > Led Driver > Led Driver Selection

Led Driver Selection

Contents

To get that exact lumens output for each color, you’d typically employ a microcontroller (MCU) and the MCU can also do a DC-to-DC power conversion as well as any communications that But that is not the only thing you have to take into account when selecting the driver. TRIAC dimmers are common hardware store and household dimmers, which include brand names such as Lutron and Leviton. As each number increases, so does its level of protection.

It also offers a fast transition between two regulated LED currents in less than 2 µsec, enabling more accurate color mixing in RGB applications. (Courtesy of Linear Technology) Other key features A 10-volt signal on the dimming wire will allow for maximum current to flow to the LEDs for maximum intensity. OSRAM Opto Semiconductors 8. An efficiency of 80 percent or higher is recommended for operating LEDs.  Size When choosing a driver or power supply, the size of an LED product's housing or area of installation is

What Size Led Driver Do I Need

If the specs don’t mention dimming at all, it is safe to assume that the product is not dimmable, and the same goes for household LEDs with internal drivers. Summary Lighting designers need to know four key specs before they think about selecting a driver, always keeping in mind their expertise and knowledge in power design, which can influence the The information below should help you pick the right power source for your needs.

  • Adding this 20% cushion will prevent the power supply from being over-worked.
  • Where is your luminaire designed to be used in?
  • Overworking the power supply can cause the LEDs to flicker or cause premature failure of the power supply.
  • Multiple dimming interfaces 5.
  • Using an LED Boost Driver (FlexBlock) The FlexBlock LED drivers are boost drivers which means they can output a higher voltage than what is supplied to them.
  • Power factor tells you how much of a real power load the driver puts on the electrical network.
  • Most LED driver vendors agree that once the LED is selected there are four key specifications that LED lighting designers need to know—input voltage range, output voltage of the LED string,
  • And are the approvals for Europe (ENEC) or America (UL).
  • Higher drive currents will result in more light from the LED, and will also require more wattage to run the light.
  • to 4 p.m.

Most drivers accept a wide range of input voltages. Once the system specs are known, including lumens per watt required for the system and lumens per watt of the LED, designers need to know the input voltage range, output voltage Constant-current LED drivers shown installed on an LED can light fixture and LED disc bulb Constant-Voltage Power Supplies Constant-voltage power supplies can be used to power LED products that have resistors or constant-current Led Drivers Basics Note: Using any constant-current driver (dimmable or not) requires some electronic circuit design experience for a successful project.

With constant current driver, it is easier to manage the right brightness. Led Driver Calculator So, if you had 500:1 and 10:1, you can achieve a 5000:1 contrast ratio if you’re able to use those,” Perry explained. Wide input voltage range 9. Käsittääkseni voisin tökätä kiinni jännitelähteeseen kunhan laitan vain oikean etuvastuksen kiinni sarjaan mutta olisiko jonkinlainen driveri parempi vaihtoehto?

The latest technology feature trends in LED drivers are, 1. Best Led Driver Manufacturers So there you have it. Waterproof. This change in power on the AC input side will vary the voltage on the DC output side and control the intensity of the LEDs.

Led Driver Calculator

These will obviously have an impact on your driver selection. http://www.lutron.com/en-us/Service-Support/Pages/Technical/Design-SelectionTools/LEDBuildAModel.aspx Decoder Max Load is 3A per channel which I am well under, the Max output power is 1728Watts again well under. What Size Led Driver Do I Need Vo + (Vf x LEDn) = Vin Where: Vo = Voltage overhead for drivers – 2 if you are using a DC LuxDrive driver or 4 if you are using an Led Driver Specification Sheet Reply ↓ Robert December 6, 2015 at 9:41 pm Hi, I want to power a bunch of 5mm leds (because they look cool, have higher CRI (Yuji) and are not nearly

In most applications using a low voltage DC input LED driver is recommended. A Class II rating refers to a double insulation layer between AC input and DC output wires. If you have an LED product with 12-volt DC operation that you wish to use in a 120-volt AC home wiring system, you'll need a power supply that includes 120 volts NOTE: It is important to consider the minimum output voltage of off-line drivers when designing your application. Led Drivers Circuit Diagram

We also have this Driver Selector tool that helps calculate what driver would be best by inputting your circuit specs. It has a very easily settable over-temperature protection via one resistor, said Cartwright. Step four: Do you need dimming? The LED will continue to get hotter and draw more current until the LED burns itself out, this is also known as Thermal Runaway.

I do want ample protection for longevity of the system so I was thinking to use resistors at each LED for a second line of protection even if I used a Led Drivers Tutorial For instance, the driver above has a minimum output of 15 volts. UL Class 1 drivers have a high-voltage output and safety protection is required within the fixture.

About this author Gina Roos For more than 20 years, business and technology writer Gina Roos has contributed both print and web articles to influential trade publications in the electronics industry.

Also be sure that the power supply or driver's input voltage matches that of the location it will be installed in. In order for that light strip to be installed in a home with a 120-volt alternating current (AC) wiring system, the voltage would need to be reduced and converted from AC Each feature is designed around what is most important to you – how well your building is working.Learn moreService & SupportTaking care of the customer is Lutron’s first principle and our Top 10 Led Driver Manufacturers So if you were in Boost-Only mode you could power up to 16 LEDs (48/2.9).

Of course, if it continues to get hotter, it will shut down based on the temperature profile programmed with the resistor. By simply selecting whether your LED driver should be constant current vs. Your driver must accept the input voltage of the place you’re using your light so it can properly step it down to the right output voltage. For smaller applications there are more dimming and output options available compared to high voltage AC drivers so you have more to work with in your application.

Sign up for our blog digest! And what type of dimming? A need for dimming is mainly dependent of the specification of your luminaire. Only a couple of our strips take 24VDC in and those tend to be higher powered LED strips, is there a reason you need 24VDC input?

LED drivers are divided into two different categories: constant current and constant voltage drivers. Learn how to update your browser Would you like to answer a few questions about our website? Once they start down that path we ask them if they are willing to make some small changes in their LED string and many times they are, which results in saving Resistive Dimming: Resistive dimming can be used to control dimmable power supplies such as Mean Well HLG Series.

Constant-Current Drivers LEDs typically have a power-limiting device (either driver or resistors) in order to prevent LEDs from being overdriven. When choosing a constant-current driver for an LED project, ensure that the current and voltage requirements of the LEDs are met.