Home > Led Driver > Led Driver Ic Flashlight

Led Driver Ic Flashlight

I could use your vote for the laser cutter contest :)vgreene (author)Reply2012-09-18Very nice well documented build. Why are the French and Indian Wars / Seven Years' War not considered WW 1? This circuit is easily adaptable to support PWM dimming.***DANGER  UV LIGHT IS DAMAGING TO THE EYES *** PLEASE USE THE PROPER EYE PROTECTION *** ***DANGER LITHIUM BATTERIES CAN EXPLODE OR CATCH Other suppliers like Farnell (Newark) or Mouser would give similar results. http://vinaprosoft.com/led-driver/led-flashlight-driver-ic.php

My circuit discussion for the functional blocks can be found on the JPG annotation.ScorpionStinger_LED.pdfDownloadStep 2: LED Driver IC SchematicShow All Items Since each LED requires 100mA and 3.6 Volts,  it was We’d really appreciate it. The datasheets don't seem to show a constant current setup and I don't know if it can be done with these or not, but they can be pretty cheap at $0.60*1 Already have an account?

No one, except maybe your next door neighbor will know what parts you can actually get where you live. Electronic GeekLEDs Skip Social. It works with input voltages of 1 to 10V, and it can drive several serial LEDs.The trick is to choose the supply voltage. Robert Wright Kayla LaCour Women Engineers On the Rampant Sexism of Silicon Valley

  • You will lose some efficiency because of the 0.5 volt drop across the resistor, but the heat (10 mW @ Iled=20mA) from that shouldn't even be an issue.
  • I've read some of your instructables before.
  • Does a segwit based side chain like the lightning network allow for fractional reserve?
  • Input voltage can be from 2 to 7 volts, and output voltage up to 20V.
  • The LED and isolation disc (photo by Roy Wood) After the old driver was removed, the new one was installed very easily.
  • Successful test (photo by Roy Wood) If you're interested in reading a little more about flashlight tweaking and tinkering, head over to the flashlight wiki and check out the DIY P60

Also, it doesn't need a schottkey, transistor or sub-1ohm resistors so it should help keep costs down, especially with the lower value, 0806 form-factor inductor. During 30 continuous minutes of  field testing.  the Scorpion Stinger behaved very well without any heat related issues.  A comparison test between the "Drug Store" UV flashlight and the Scorpion Stinger ScorpionStinger.pdfDownloadwebench_design.pdfDownloadStep 3: Case and Battery SelectionShow All ItemsTHANK YOU HARBOR FREIGHT TOOLS!  I scored this awesome 1 Million candlepower spot light that served as the case/battery/charger for my project for just Strategies for self-learners to transition into working on larger projects Understanding Docker layers How to answer when asked "Are you able to work long hours" in a job interview?

Is receiving fake torrent data possible? I want to use two AAA Eneloop cells. Instead, use them to feed the LT1932 circuit. http://www.instructables.com/id/The-Scorpion-Stinger-A-High-Power-UV-LED-Flashli/ Using them on 1 AAA cell is therefore possible but the circuit will be non-regulating (although the LED current will be less than the set current, not more).

Quick LED Driver Search Input Vin (Min) V Vin (Max) V LED Strings # LEDs InEach String # Strings String Current A LED Voltage Min LED Second, it regulates based on voltage, not current. FEATURED RESOURCES Subscribe to RSS: or 5G Analog Automotive Components|Pkging Consumer DIY IC Design LEDs Medical PCB Power Management Sensors Systems Design Test & Measurement Blogs Design Ideas Products Tools DESIGN Either way, you are supporting our journalism.

Follow Follow UsOn Youtube Don't miss out on WIRED's latest videos. The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of Condé Nast. No co-prime neighbors Why did Vader board the disabled Rebel flagship at the end of Rogue One? Well documented and good photos.

The LED doesn't reach the set current until close to 2V, however. Powered by vBulletin Version 4.2.4 Copyright © 2017 vBulletin Solutions, Inc. Your existing password has not been changed. Account Activated Your account has been reactivated.

You can partially get around this by choosing a higher set current. I'm not asking "which product is better" or "shall I buy PC or Mac" :) –Kamil Nov 8 '14 at 17:14 1 No, that rule exists because such answers quickly This is fine for most things, but anything driving LEDs should be a current regulating device. navigate to this website A few of them look pretty cheap at Mouser, like this one.

That last mode though -- the seizure-inducing blinking mode -- was a deal breaker.This article has been reproduced in a new format and may be missing content or contain faulty links. Note that all parts except the 2 driver IC's are through hole.  Note that the LM3410 IC has a thermal pad on the body of the chip itself, which is critical So has anyone ever used this one or is there an issue with this IC that I don't see?

These are a few photos after searching with the Scorpion Stinger.  The bright green dots in the photos are the scorpions fluorescing in the UV light of the Scorpion Stinger.Videos:Scorpion Touch

Follow Advertisement. The generic form would require adding a current sense amplifier. Here is a sample search for LED controllers at DigiKey. All rights reserved.

They are quick. Some numbers to narrow the search: Duty Cycle (DC) at \$V_S\$ = 1.8V DC = \$\frac{V_o}{V_o+V_S}\$ = \$\frac{\text{3V}}{\text{3V+1.8V}}\$ ~ 0.63 Inductor ripple current (coupled Inductor): \$\text{$\Delta $I}_L\$ = \$\frac{\text{DC } V_S}{2 up vote 2 down vote favorite 1 I need a very small and light 3W flashlight/headlamp for a kind of specific purpose. Since the TPS61070 is in an SOT-23-6 package it should be fairly easy to solder by hand.

This will also make any loop compensation a little easier. Reply With Quote 06-17-2004,03:58 PM #8 pbarrette View Profile View Forum Posts Private Message Visit Homepage View Articles Flashaholic Join Date May 2004 Location Huntsville, AL Posts 346 Re: Single LED The cherry on top would be to show a movie of scorpion catching!!nmeans (author)mrfixitrickReply2012-09-17Thanks! Setting a higher resistance results in lower brightness.